alveolar ridge

Objective : To provide measuring methods and a quantity index for alveolar ridge augmentation at mandibularposterior area.

目的: 为下颌后牙区牙槽嵴增高术提供临床测量方法及定量指标.

Height measurment of mandibular posterior area for alveolar ridge augmentation: a primary study

下颌后牙区颌骨高度的测量研究

RESULTS: The alveolar ridge was vertically augmented 7.5 mm and 7.0 mm on average respectively.

结果：平均牙槽嵴增高分别为7.5,7.0mm；

Clinical study of the use of artificial hydroxyapatite bone for keeping the hight of alveolar ridge

羟基磷灰石人工骨填塞拔牙创保持牙槽嵴高度的临床研究

An investigation of relation between facial morphology and alveolar ridge atrophy in patients with edentulous jaws

面部形态与无牙颌牙槽嵴萎缩关系的初步探讨

Local Alveolar ridge deformities in the anterior area a great concern during restorative and esthetic dentistry.

在前牙区的局部骨缺损,对于赝复科及美容牙医学而言已演变为重要的议题.

Conclusion The postoperative lip pressure plays an important role for the deformation and deviation of alveolar ridge.

结论唇裂修复手术后产生的压力是使未作植骨修复的牙槽突产生变形移位的主要原因。

Three-dimensional Finite Element Analysis of Stress Distribution and Displacement of Edentulous Alveolar Ridge Retained by Conical Telescope

不同材料套筒冠义齿无牙区牙槽嵴应力、位移分布的三维有限元分析

Methods: 4 patients with vertical alveolar ridge deficiencies caused by trauma were treated with vertical distraction osteogenesis.

方法：对4例因外伤造成牙槽骨垂直向缺损，且缺损均>10mm的患者采用垂直向牵张成骨术。

A Preliminary Study of Atrophic Alveolar Ridge Augmentation Using Particle-Bioactive Glass-ceramics

颗粒型生物活性玻璃陶瓷增大牙槽嵴的初步临床观察利用种植作牵张增高牙槽嵴的实验研究

Thin maxillary alveolar ridge splitting with simultaneous implant placement: A preliminary clinical study

上颌菲薄牙槽骨劈开同期人工牙种植的初步观察

Methods Three-dimensional finite element methods was employed. A standard model of edentulous mandibular alveolar ridge was chosen.

方法采用三维有限元法，选择标准无牙下颌牙槽嵴模型为实验对象，分别建立有软衬和无软衬两个有限元模型。

Conclusion: Canine is ideal animal model for alveolar ridge augmentation.

结论：犬是理想的牙槽嵴萎缩动物模型。

Objective To prevent the alveolar ridge from atrophy after extraction.

目的为解决拨牙后牙槽嵴吸收萎缩导致修复上的困难及保持牙槽骨的正常解剖形态。

Study of alveolar ridge Absorption and root resorption during orthodontic treatment

正畸患者矫治前后牙槽嵴和牙根吸收的调查研究

Alveolar ridge reconstruction using a membrane technique and autogenous bone particles; a clinical study

自体松质骨支持引导组织再生膜重建牙槽嵴的初步临床研究

Results: No difference was found in the PPT of alveolar ridge mucosa between the left and the right side.

结果：无牙颌患者同颌左右侧牙槽嵴粘膜测试点的疼痛阈之间无显著性差异。

Objective : To provide a quantity index for alveolar ridge augmentation at mandibular posterior area.

目的: 为下颌后牙区牙槽嵴增高术提供定量指标.

If the alveolar ridge is low and even, wecan take impression two times to get a accurate impression.

牙槽嵴低平的患者采用二次印模法可取得较准确的印模。

Study of decalcified dental matrix in alveolar ridge augment with modified sandwich techniques in dogs

种植体固定的三明治法增高牙槽嵴的实验研究脱钙牙基质改良三明治术增高牙槽嵴的研究

Clinical Application of Distraction Osteogenesis in Vertical Alveolar Ridge Augmentation

喉垂直部分切除术；牵张成骨垂直升高牙槽骨的临床应用

An animal having teeth consolidate with the inner surface of the alveolar ridge without sockets.

长有由内表层无牙槽固定的牙齿的动物。

The stress value of mucosa on bilateral molar teeth alveolar ridge crest was relatively larger.

双侧磨牙区牙槽嵴顶处的黏膜应力值相对较大；

The bone absorbing and the alveolar ridge descending was followed by the missing tooth.

牙缺失时，骨质吸收牙槽突降低。

A Preliminary Study of some Factors Influencing the Resorption of Edentulous Alveolar Ridge

影响无牙颌牙槽骨吸收的某些因素的初步研究

Cases is because of bad alveolar ridge appearance;

牙槽嵴形态不好的4例；

Implantation of Hydroxylapatite-plaster of Paris Used to Increase the Height of Alveolar Ridge

羟基磷灰石-煅石膏复合材料植入增高牙槽嵴的临床应用

In this study, a three-dimensional finite-element stress analysis was used. A model of mandibular alveolar ridge was chosen.

本文采用三维有限元应力分析法，以下颌牙槽嵴模型为实验对象，建立起三个有限元分析模型：无软村模型、有软衬模型和无粘膜无软衬模型。

Complete denture restoration on edentulous jaw with flabby alveolar ridge

松软牙槽嵴无牙颌的全口义齿修复

This research aims to study the changes of TMJS and masticatory muscles after alveolar ridge augmentation.

本课题拟通过钛镍记忆合金牵张装置增高牙槽嵴的方法，来观察牙槽嵴增高对颞下颌关节及咀嚼肌的影响。